Pass B1

[sachu888]

This is good news Sachin. Any idea when you will be receiving the parts?

Thanks.

20 days (approx).I may be able to ship B1 kits early Jan 2013.

Regards,
Sachin

 

[quad]

How's this for a 5 channel source selector? Eagle files available, of course.

Got some good inputs from Om and Sachin, and we are nearly done with the design of
the source selector board. Hope Sachin can help us with group buy if there is interest.

It looks like this now.

 

[sachu888]

Got some good inputs from Om and Sachin, and we are nearly done with the design of
the source selector board. Hope Sachin can help us with group buy if there is interest.

It looks like this now.

Thanks Prasad,
It looks very good now.we can start a small GB here approx cost should be Rs600-800

Regards,
Sachin

 

[sann]

approx cost should be Rs600-800

Hi Sachin, cost is for the kit or the pcb?

 

[sachu888]

Hi Sachin, cost is for the kit or the pcb?

Kit.

Regards,
Sachin

 

[sann]

In for 1 kit.
-sann

 

[quad]

Source Selector GB
==============
Sann - 1 kit
Quad - 1 kit + PCB

 

[keith_correa]

I'm in for 3 Source Selector kits

 

[captrajesh]

I'm in for a kit too. BTW, how do we power this thingy?

 

[sachu888]

I'm in for a kit too. BTW, how do we power this thingy?

We can take power from existing B1 power supply.It has onboard 12v regulator.

Regards,
Sachin

 

[quad]

I'm in for a kit too. BTW, how do we power this thingy?

Capt, it has 2 ways to power it -

1) Regulated 12V source available in the chassis - use the connector on left side of PCB.
Do not install the voltage regulator.
2) Input voltage is more than 12V - use the connector on right side. Install the
7812 voltage regulator chip, with a heatsink if needed.

Resistor values etc are designed for 12V supply and relays.
But the board can be used with other voltages like 5V or 6V also, provided
you use the appropriate relay, and install the appropriate resistors.

 

[apk]

count me also in for 1 source selector kit

Thanks,
APK

 

[rohitmusic]

Source Selector GB
===============
Sann - 1 kit
Quad - 1 kit + PCB
keith_correa - 3 kit
captrajesh - 1 kit
apk - 1 kit
rohitmusic - 1 kit

+1 kit for me

 

[omishra]

Capt, it has 2 ways to power it -

1) Regulated 12V source available in the chassis - use the connector on left side of PCB.
Do not install the voltage regulator.
2) Input voltage is more than 12V - use the connector on right side. Install the
7812 voltage regulator chip, with a heatsink if needed.

Resistor values etc are designed for 12V supply and relays.
But the board can be used with other voltages like 5V or 6V also, provided
you use the appropriate relay, and install the appropriate resistors.

This is great! We will be getting part names ON PCB while values will be dependent on selected relay voltage.

 

[santnai]

Hi Mishraji/Sachin,

I would appreciate your help in integrating Pass b1 with CNC and SSP by helping me out with the connection circuit diagram in the attached picture. It will be of great help for the other newbies like me.

Regards,

Santosh

 

[omishra]

Hi Mishraji/Sachin,

I would appreciate your help in integrating Pass b1 with CNC and SSP by helping me out with the connection circuit diagram in the attached picture. It will be of great help for the other newbies like me.

Regards,

Santosh

Please look at http://www.hifivision.com/diy/21036-pass-b1-31.html
and

http://www.hifivision.com/diy/21036-pass-b1-76.html

If you could not understand please ask.

 

[TheCoolestOne]

Source Selector GB
===============
Sann - 1 kit
Quad - 1 kit + PCB
keith_correa - 3 kit
captrajesh - 1 kit
apk - 1 kit
rohitmusic - 1 kit
TheCoolestOne - 1 kit

+1 kit for me

+1 kit for me too. Very much required.

 

[atharva]

+1 for the input switch

 

[ruenigma]

Ok me too for input switch

 

[gobble]

+ 1 for me. How much Saar?

--G